High Res Wifi Signal Mapping
Channel:CNLohr · Length:6:39 · Published:2015-02-14 · Views:551115
Summary
CNLohr maps Wi-Fi signal strength at high resolution by moving an ESP8266 on a CNC mill, then visualizes the 3D data in WebGL. The result shows interference patterns in space.
Why HN recommends it
Cited as a cool, concrete visualization of Wi-Fi interference patterns.
the space is basically riddled with interference patterns — HN, 2017
Networking & internet infrastructure · Data visualization & information design · Embedded systems & DIY electronics
Subtitles (excerpt)
In Adam's hand here is an ESP8266 hooked up to a single WS2812 LED and a little Hubsan battery pack. This is a battery powered ESP8266 now. While the ESP8266 can tell RX power, I'm not using it for that. I'm actually causing my computer to connect to it and ping it, and there's an application on my computer that looks at RX power of those pings and send a color to the ESP8266, so as Adam moves around in 3 dimensional space, you can see the realtive strength changing. This looked kinda random to me at first until I started to actually play with it, and then I realized it's not random, it's really telling you the actual RX power in every point. So, as he moves through the same area, you can see that it turns red to green to blue. There's a nice solid blue. You can see the variations to quite the degree. It's crazy how quickly the RX power can change from just a little bit, moving just a couple inches in one direction or another causes massive changes in the RX power. I decided to do a couple things with this, one of them was to go play with a really long exposure on my camera. First I configure a camera pointed at the area I'd like to check, I set it to the lowest ISO possible and a relatively large aperature, and uuh 60 FPS
On Hacker News
CNLohr made a similar project three years before that: [VIDEO] I know this stuff is dystopic, but I personally find it really cool. That said, I also disable WiFi and prefer ethernet wherever possible... — TechBro8615, 2023-09
I saw a post a while ago where someone made a map of their room by moving some sensor (measured either noise level or wifi signal) around with stepper motors. Edit: [VIDEO] — andai, 2024-06
I've also achieved substantial improvement with simple parabolic shaped, ~40 cm wide aluminum foil constructions, but there always seemed a bit luck involved and it needed some tweaking. Not sure whether the foil mainly acted as shielding that reduces the noise floor from other directions. I've read in other forums that fiddling with aluminum foil is mostly luck because additional reflective surf… — tqdm, 2017-12
Related videos
- Starbase Tour with Elon Musk [PART 2 // Summer 2021] · Everyday Astronaut · 1:01:18
- Starbase Tour with Elon Musk [PART 1 // Summer 2021] · Everyday Astronaut · 53:17
- A Better Default Colormap for Matplotlib | SciPy 2015 | Nathaniel Smith and Stéfan van der Walt · Enthought · 19:08
- 8-bit computer update · Ben Eater · 6:53
- Reverse emulating the NES to give it SUPER POWERS! · suckerpinch · 22:21
- “Hello, world” from scratch on a 6502 — Part 1 · Ben Eater · 27:24
- Hans Rosling's 200 Countries, 200 Years, 4 Minutes - The Joy of Stats - BBC · BBC · 4:47
- Harder Drive: Hard drives we didn't want or need · suckerpinch · 36:46
- Shenzhen: The Silicon Valley of Hardware (Full Documentary) | Future Cities | WIRED · WIRED Investigations · 1:07:51
- This Video Is Sponsored By ███ VPN · Tom Scott · 7:25
- "Programming a 144-computer chip to minimize power" - Chuck Moore (2013) · Strange Loop Conference · 40:12
- Wealth Inequality in America · politizane · 6:23
- Animations of unseeable biology | Drew Berry | TED · TED · 9:08
- The world's worst video card? · Ben Eater · 32:47
- A New Way to look at Networking · Google · 1:21:15
- Immigration, World Poverty and Gumballs · NumbersUSA · 6:08